Key Features Marks Where Others Can't The long 1-1/2 inch nose lets you mark inside holes, along walls, and into corners that a standard marker tip cannot reach. That means fewer guess marks and less rework when layout has to...
Marks Where Others Can’t The long 1-1/2 inch nose lets you mark inside holes, along walls, and into corners that a standard marker tip cannot reach. That means fewer guess marks and less rework when layout has to be right the first time. Thin Tip, Clean Layout The 0.9 millimeter ultra-fine point is built for precise marking, especially on detailed woodworking, cabinetry, and trim work. You get a clear line without the fat mark that can throw off fit and alignment. Two Tips, One Marker One end handles fine layout work and the other gives you a 7 millimeter chisel tip for broader marks. That makes this permanent marker more useful on the bench and on the jobsite without carrying a second marker.
The FastCap Long Nose Marker Thin Black is a dual-ended permanent marker built for layout work where a regular marker comes up short. This is a permanent marker designed for precise layout marking in tight spaces. Model Number: FC-02508. If you need to mark inside hardware holes, trace along a wall, or reach past an edge without smearing a wide line, this is the kind of marker that actually solves that problem.
The main reason to buy this marker is the extended 1-1/2 inch reach paired with a 0.9 millimeter ultra-fine tip. On real work, that matters because you can get the point into places your fingers and a standard marker body cannot fit. Instead of estimating hole locations or transferring a line with another tool, you can put the mark exactly where it needs to go.
FastCap also made it more useful than a one-trick specialty marker by putting a 7 millimeter chisel tip on the other end. That gives you a fine point for detailed layout and a broader tip for general marking. If you’re moving between precise cabinet hardware marks and quick jobsite notes or cut marks, you do not need to swap markers every few minutes.
The ink is listed as permanent and waterproof, which makes this marker a better fit for jobsite use than a basic office marker. Marks stay visible on common work surfaces like wood, plastic, metal, glass, ceramic, paper, cardboard, and vinyl. That broad surface compatibility makes it useful in a shop, van, or site box where materials change from task to task.
From a design standpoint, the narrow nose is the whole story here. The body is shaped like a purpose-built layout tool, not just a standard marker with a fine tip. That extra reach helps when you’re marking through guides, templates, brackets, clips, and other parts where access is limited. For cabinet installers, trim carpenters, woodworkers, and punch-list guys, that can save a surprising amount of time over the course of a day.
The FastCap Long Nose Marker Thin Black makes the most sense for tradespeople and serious DIY users who care about accurate marking more than general writing comfort. If most of your work is rough framing and broad marks, a standard carpenter marker may be enough. But if you work around finish materials, hardware placement, detailed fitting, or tight access, this layout marker earns its spot fast.
This is where the long nose design pays off. Instead of trying to eyeball a mark or coming back with a pencil after removing the part, you can mark directly through openings and around installed pieces.
The dual-ended layout marker setup is practical. Use the 0.9 millimeter tip when the line needs to be exact, then flip to the chisel tip when you need a more visible general mark.
| Marker Type | Permanent marker |
|---|---|
| Model Number | FC-02508 |
| Ink Color | Black |
| Fine Tip Size | 0.9 mm |
| Chisel Tip Size | 7 mm |
| Extended Reach | 1-1/2 in. (38 mm) |
| Water Resistance | Waterproof |
| Recommended Surfaces | Wood, glass, plastic, metal, ceramic, paper, cardboard, vinyl |
Cabinet Installation Trim Carpentry Woodworking General Contracting Remodeling DIY / Hobbyist Hardware Layout Precise Marking
Use the long nose tip to mark hardware and bracket holes before removing the part from the workpiece. It is faster and usually more accurate than trying to transfer the location after the fact.
1 Year warranty.
Tool Nut’s Take
The FastCap Long Nose Marker Thin Black is one of those simple tools that makes a lot of sense the first day you use it.
There are no reviews yet.
Shopping Over $40 you will get 100% free shipping
